Linda moved into the guest room in the fall of 2021. Not because we were fighting. Because I snored like a diesel engine idling in a cold driveway, and she is a light sleeper who needs her sleep more than she needs my company at two in the morning.
That got me to a home sleep test, which came back moderate obstructive sleep apnea, which got me a CPAP machine with a nasal pillow mask that I have used for about three years. That machine is the reason I am not writing this from a recliner at noon. The Somnofit-S mouthpiece from SnoreLessNow is a different tool for a different job, and I fit mine on the kitchen counter with a saucepan, a pair of tongs and about twenty minutes of actual work.
Before the steps, the part that matters more than any of them. If you have diagnosed sleep apnea, a mouthpiece is not a treatment for it. It is not a substitute for the machine, and it is not something you use instead of seeing your doctor. My apnea is managed with CPAP and I check in with my doctor about all of it. If you have not had a sleep study, go get one. That is the whole disclaimer and I mean every word of it. What follows is a guy describing how he molded a piece of plastic so it stopped gagging him.
A mouthpiece is only as good as its fit. This is the one I molded at my own counter.
The Somnofit-S is boil and bite, adjustable, made in Switzerland and cleared by the FDA. It is about 40% smaller than most mouthpieces on the market, which matters if your gag reflex has opinions. Check the size and material details before you give up an evening to it.
Amazon Check Today's Price on Amazon →Step 1: Try It In Your Mouth Before You Boil Anything
This is the step I skipped the first time, and it cost me a mouthpiece. Take it out of the package and put it in your mouth cold. Just hold it there for a minute. You are checking two things: whether your gag reflex is going to fight you, and whether your jaw has room to close around it.
The listing puts the whole package at 4.72 by 3.94 by 1.97 inches and 5.29 ounces, and the piece itself is about 40% smaller than most mouthpieces on the market. I cannot verify that number against every competitor on earth. I can tell you it sat further forward in my mouth than the bulky thing I tried years ago, and further forward means less gagging. I have a wide jaw and a strong gag reflex, and this one did not set it off.
It is made of a thermoplastic polymer and it is free of BPA, latex, phthalates and silicone. The silicone part mattered to me. Every silicone thing that has ever been in my mouth has made me want to spit it across the room. This is not silicone, and I noticed the difference in the first ten seconds.
My first attempt went into a pot of water before I did any of this. I was in a hurry, I boiled it, I bit it, and it came out lopsided because my jaw was tense and I had no idea what a correct bite felt like yet. Do the cold test first. It takes a minute and it tells you whether the rest of the evening is worth spending.
If you have crowns, a bridge, dentures, or a tooth that is loose, stop right here and call your dentist before you mold anything. I have a crown on the lower left and I asked first. That is a five minute phone call that protects dental work you paid good money for.
Step 2: Boil the Water, Then Take It Off the Heat
Fill a saucepan with enough water to cover the mouthpiece. Bring it to a rolling boil, then pull the pan off the burner and let it sit for a beat. Not a long beat. A slow count of ten.
Here is why I say off the heat. Water still at a full roll is right at the edge of what a thermoplastic wants to feel, and a mouthpiece that goes in too hot comes out soft enough to fold on itself. You want it pliable, like a hard candy that has been in your pocket all afternoon, not limp.
I learned that on a Thursday night in February, standing over the stove with a candy thermometer I borrowed from Linda's baking drawer. Water boils at about 202 degrees here in Colorado Springs, which is lower than sea level and confused me for a solid minute. I pulled the pan off, waited my ten count, and the mouthpiece came out soft but not floppy. The batch before that one, straight off a rolling boil, folded in half like a wet noodle and I had to throw it out and start over.
Drop it in with tongs, not your fingers, and leave it in for the time the instructions give you, which for me was under two minutes. The instructions that come with the SnoreLessNow mouthpiece are short and worth reading twice, because water temperature and soak time are the two things that decide whether the mold works. Get either one wrong and you will be doing this again next week.
While it soaks, get set up. Mirror at eye level. A towel on the counter. A bowl of cold water within arm's reach. You have about thirty seconds once it comes out, and you do not want to spend fifteen of them looking for a bowl.
Step 3: Bite Down Evenly and Hold Still
Fish it out with the tongs, shake it once, and get it onto your upper teeth. Then bite down. Not a clamp. An even, steady pressure, back teeth together, lips relaxed, shoulders down. You are not trying to win a fight with it.
The Somnofit-S uses what the company calls an Even Pressure Distribution System. On the kitchen counter that translates to this: when you bite, the force spreads across your whole arch instead of loading up one spot near your back molars. That is the difference between a mouthpiece that stays put and one that digs in on the left side and has you taking it out at 3 a.m.
Keep your tongue on the roof of your mouth and breathe through your nose while you hold. If you breathe through your mouth, your jaw drifts and you mold the thing into a position your jaw never actually rests in. Hold a slow count of thirty. Then drop it straight into the cold water and leave it there for a couple of minutes. That cold dunk is what sets the shape. Skip it and you will have a mouthpiece that slowly sags back toward its original form.
My first mold, the hurried one from before I read anything, sat about an eighth of an inch off center. You could see it against a flat counter. That small a gap does not sound like much until you wear it for a night and feel every bit of the pressure on one side of your jaw by midnight. The second mold, done slow with my shoulders down and my tongue up, came out even, and I could tell the difference before I ever got into bed.
Linda came back to the bedroom on a Tuesday, six weeks after the first mold. She brought her own pillow. That is the only review that ever mattered to me.
Step 4: Check the Fit, Then Use the Adjustment
Put it back in once it is cold. It should seat onto your upper teeth with light pressure and stay there when you open your mouth. If it drops off when you talk, the mold did not take and you get to try again.
The SnoreLessNow mouthpiece is adjustable, and that is the difference between a gadget you throw in a drawer and one you keep using. A first mold that comes out a little off is not a dead end. You can move it and refit it without ordering a new one and starting over.
Then do the boring test. Wear it for half an hour while you watch the evening news. Notice whether you are swallowing constantly, whether your jaw aches, whether you want it out. A little extra saliva for the first two or three nights is normal in my experience. Jaw soreness that lasts past the first week is not, and that is your signal to refit or to stop and talk to your dentist.
Night one I lasted about four hours before I took it out and set it on the nightstand. Night two I made it to about five. Night three I slept through until the alarm, which had not happened in a while. I wrote the times on the calendar that hangs by the kitchen phone, mostly because Linda wanted to see it in writing, and by the end of that first week the entries stopped being interesting. That is the goal. Boring entries.
Step 5: Clean It Every Morning and Let It Dry
Rinse it under warm water every single morning, before coffee, before anything else. Scrub it with a toothbrush you keep for that purpose and nothing else. A drop of dish soap is plenty. A denture tablet once a week if it starts smelling like a gym bag.
Then let it air dry somewhere it will not pick up lint, and put it away dry. A mouthpiece stored wet in a closed container is a science experiment by Thursday. Mine lives on a clean washcloth on the bathroom shelf, which is not fancy, but it works.
Check the fit every couple of weeks. Thermoplastic moves a little with heat and time, and a mouthpiece that fit in January can feel loose in July. If it gets sloppy, run the boil and bite again. That is a ten minute job the second time around.
What Else Helps
The mouthpiece is one piece of a bigger picture, and I would be lying if I told you it did all the work at my house.
The machine stays. I use CPAP most nights. The mouthpiece goes in the travel bag and comes out when I am somewhere the machine is not practical, or on a night when my nose is so stopped up that the nasal pillows are useless. That is a plan I made with my doctor, not something I decided in the garage at midnight.
Sleeping on my side helps me. So does a humidifier in the winter, because Colorado air at this altitude is dry enough to crack a lip by February and a dry mouth makes everything worse. Mine is a plain one with a gallon tank, and I fill it every other night from October through April. When I forget, I wake up with a mouth like a dustpan and the mouthpiece feels like it is stuck to my teeth. That is not the mouthpiece's fault. It is the dry air, and it is the one part of this routine that costs nothing but a little attention.
A nightcap does not help. I gave that up. Dropping about fifteen pounds over two years helped more than any gadget I have bought.
And give it a week before you decide. The first night with any mouthpiece is strange. The second night is less strange. By the fifth night I was putting it in without thinking about it, and Linda had stopped waking up at the sound of me rolling over. If you want the longer version of how this held up over months, I wrote that up separately, and I also put it side by side with the old boil and bite style so you can see what actually changed.
One mold, one week, and a bed partner who stops leaving the room
The Somnofit-S from SnoreLessNow is boil and bite, adjustable, made in Switzerland and cleared by the FDA. It is not a treatment for sleep apnea and it is not a replacement for a CPAP machine. It is a well made mouthpiece for the nights you need one. Read the size and material details before you order.
Amazon Check Today's Price on Amazon →