Linda moved into the guest room in October and I pretended it did not bother me. Thirty-four years of marriage, and my snoring finally outvoted me. She carried her pillow and a paperback under her arm and never said a word, which was worse than if she had. I lay in that quiet room twenty minutes, then sat at the kitchen table in the dark because I did not feel like going back in there alone. I had been a loud sleeper close to twenty years by then.

Here is the part I want straight before anything else. I have moderate obstructive sleep apnea. A home sleep test in 2021 found it, after Linda noticed I would stop breathing and then gasp. My doctor set me up with a CPAP machine and a nasal pillow mask, and I have used it about three years. The CPAP is the medical treatment.

A person holding the anti-snore mouth guard over a bathroom counter next to a pot of hot water.

What I was actually shopping for were the nights the CPAP did not happen, and that is where SnoreLessNow came in. A nap in the recliner. A long drive I still take now and then. Nights when the mask felt like too much trouble at eleven o'clock. On those nights I snored like a truck with a bad exhaust, and Linda paid for it. I wanted something for the gap, not a replacement for the machine.

The Somnofit-S is an anti-snore mouth guard from SnoreLessNow. It is made in Switzerland, it is FDA cleared, and the listing says it is 40 percent smaller than most mouthpieces on the market. That last number is the one that got my attention. I had tried a drugstore boil-and-bite guard years ago and quit on it inside a week, because it felt like sleeping with a hockey puck behind my teeth.

So I ordered one. Here is how the first month actually went, including the parts that were not great.

The Somnofit-S is 40 percent smaller than most mouthpieces on the market. On a 62-year-old jaw, that number mattered more than any other line on the box.

The Mouth Guard Built for the Nights the Machine Stays in the Case

Made in Switzerland, FDA cleared, and molded at home in a pot of hot water. Rated 4 out of 5 by more than 1,700 buyers.

Check Today's Price on Amazon →

Molding is the usual hot water routine. Boil water, drop the guard in until it goes soft, let it cool enough to handle, then bite down and hold while it sets. My first try was still too warm and I bit too hard, so it did not sit right and I did it again the next night. The second one took. I used a two-quart saucepan and let the water come off a full boil before I dropped it in, then I held the bite and counted slowly to thirty and then to forty, because I wanted to be sure it had set instead of guessing at it. The thermoplastic polymer is BPA free, latex free, phthalate free and silicone free, which matters more to me at 62 than it did at 40, mostly because this thing sits in your mouth for seven hours at a stretch.

A couple in bed at night, one asleep on his side and the other settled in beside him under a dim lamp.

The fit is adjustable, and the Even Pressure Distribution System is the part I noticed around night four. My old guard pressed hard on my two front teeth and I would wake up with them aching. This one spreads the load out across the row. I still know it is in there. I just stop thinking about it after about ten minutes, which is more than I could say for the last one.

The honest downsides. It takes two or three nights to get the molding right, and if you rush it you are doing it over. It is also not a night I would wear it with a stuffed nose. Our bedroom runs dry most of the year, partly the altitude and partly the furnace going from November into March, so there are stretches when the nose just is not cooperating. For me, a guard is a nose-breathing night. The first week I also drooled enough to want a fresh pillowcase every morning, which I have not done since I was a kid. That settled by week two and I have not thought about it since.

After about two weeks Linda moved back into the bedroom. It was a Thursday, the second week of November, and she came in with her pillow and set it on her side without making a production of it. Not because I had gone silent. She says the sawing sound is mostly gone and what is left sounds closer to heavy breathing. That is her report from the next pillow, not a lab result, and I am not going to dress it up as one. I still wear the CPAP on a normal night. The guard covers the rest. She has been back in that bed since, and the guest room has gone back to being a guest room, which is all I really wanted out of the whole business.

What I'd Tell You If We Were Sitting at My Kitchen Table

If you snore loud enough that your partner leaves the room, get a sleep study before you buy anything. That is the first thing I would say, and I would say it twice. Pauses in breathing, gasping, waking with a headache, nodding off in the afternoon, those are not snoring problems. They are apnea problems and they belong to a doctor. A mouthpiece bought off a listing page cannot tell you whether your airway is closing at night. Only a test does that.

Second thing. If you are already treated and you want something for the odd night away from the machine, or you are a plain snorer with a clear sleep test and a light-sleeping partner, the Somnofit-S from SnoreLessNow is the best of the three I have tried. Give the molding two honest attempts, not one. And give it a week before you make up your mind, because for the first three nights I was fairly sure I had wasted my time.

Before the Guest Room Becomes Permanent, Try the Small One

Boil-and-bite molding, adjustable fit, made in Switzerland. One purchase, and you can remold it if the first attempt is off.

See the Somnofit-S on Amazon →